Exemples d'utilisation de "наклона" en russe

<>
После регулировки наклона выберите Я вижу пол. When ready, select I see the floor.
Резеро балансирует, постоянно измеряя угол наклона с помощью сенсора. Rezero keeps his balance by constantly measuring his pitch angle with a sensor.
Обратный угол наклона зубцов и бороздки на костях, указывает на ленточную пилу. Well, the negative hook angle and the striations on the bones indicate a band saw.
Продолжить трендовую линию без изменения ее угла наклона, передвигая за контрольную точку. To continue a trend line with the fixed angle moving it with control points.
Щелкнув по одному из концов линии, Вы сможете изменить положение наклона линии на графике. If you click on either end of the line, you will be able to edit the positioning of that point on the chart.
Приложение 3: Порядок определения точки " Н " и фактического угла наклона туловища на сиденьях механических транспортных средств Annex 3: Procedure for determining the " H " point and the actual torso angle for seating positions in motor vehicles
" объемный механизм определения точки'Н'" означает устройство, применяемое для определения точки " Н " и фактического угла наклона туловища. " Three-dimensional " H " point machine " means the device used for the determination of " H " points and actual torso angles.
Если вы щелкните по одному из концов нижней линии, Вы сможете изменить положение наклона объекта на графике. If you click on either end of the upper line, you will be able to edit the positioning of that point on the chart.
Приложение 4- Процедура определения точки " Н " и фактического угла наклона туловища сидящего в автомобиле водителя или пассажира Annex 4- Procedure for determining the " H " point and the actual torso angle for seating positions in motor vehicles
Приложение 15- Процедура определения точки " Н " и фактического угла наклона туловища в сидячем положении в механических транспортных средствах Annex 15- Procedure for determining the " H " point and the actual torso angle for seating positions in motor vehicles
Приложение 3- Порядок определения точки " Н " и фактического угла наклона туловища водителя, или пассажира, сидящего в транспортном средстве Annex 3- Procedure for determining the " H " point and the actual torso angle for seating positions in motor vehicles
Приложение 8: Процедура определения точки " H " и фактического угла наклона туловища в сидячем положении в механических транспортных средствах Annex 8- Procedure for determining the " H " point and the actual torso angle for seating positions in motor vehicles
Приложение 6- Процедура определения точки " H " и фактического угла наклона туловища в сидячем положении в механических транспортных средствах Annex 6- Procedure for determining the " H " point and the actual torso angle for seating positions in motor vehicles
ПРИЛОЖЕНИЕ 5, ПОРЯДОК ОПРЕДЕЛЕНИЯ ТОЧКИ " Н " И ФАКТИЧЕСКОГО УГЛА НАКЛОНА ТУЛОВИЩА В СИДЯЧЕМ ПОЛОЖЕНИИ В МЕХАНИЧЕСКИХ ТРАНСПОРТНЫХ СРЕДСТВАХ ANNEX 5, PROCEDURE FOR DETERMINING THE " H " POINT AND THE ACTUAL TORSO ANGLE FOR SEATING POSITIONS IN MOTOR VEHICLES
Поправки для тех случаев, когда конструктивный угол наклона спинки не составляет 25°, указаны в таблице IV пункта 5.4. The correction for design seat-back angles other than 25°is shown in Table IV under 5.4.
Приложение 9: Определение и резкость светотеневой границы для передних противотуманных фар и процедура регулировки угла наклона фар при помощи этой светотеневой границы Annex 9: Definition and sharpness of the cut-off line for front fog lamps and aiming procedure by means of this cut-off line
" Исходная ось "- это определенный отрезок прямой, одним из концов которого является исходный центр и который используется для определения угла наклона светоотражающего устройства. " Reference axis ", a designated line segment originating on the reference centre which is used to describe the angular position of the retro-reflective device.
" фактический угол наклона туловища " означает угол, измеряемый между вертикальной линией, проходящей через точку " Н ", и линией туловища посредством кругового сектора механизма 3-D Н. " Actual torso angle " means the angle measured between a vertical line through the " H " point and the torso line using the back angle quadrant on the 3-D H machine.
Приложение 9- Определение и резкость светотеневой границы для фар, испускающих симметричный луч ближнего света, и процедура регулировки угла наклона фар при помощи этой светотеневой границы Annex 9- Definition and sharpness of the " cut-off " line for symmetrical passing-beam headlamps and aiming procedure by means of this " cut-off " line
Приложение 9- Определение и резкость светотеневой границы для фар, испускающих симметричный пучок ближнего света, и процедура регулировки угла наклона фар при помощи этой светотеневой границы " Annex 9- Definition and sharpness of the " cut-off " line for symmetrical passing-beam headlamps and aiming procedure by means of this cut-off line "
Les exemples sont fournis uniquement à des fins linguistiques, c'est-à-dire pour étudier l'utilisation de mots dans une langue et leurs traductions dans une autre. Ils sont extraits automatiquement des sources ouvertes en utilisant des algorithmes de recherche de données bilingues. Si vous trouvez une erreur d'orthographe, de ponctuation ou autre soit dans l'original ou dans la traduction, utilisez l'option "Signaler un problème" ou écrivez-nous.

Dans cette section, vous pouvez voir comment les mots et les expressions sont utilisés dans différents contextes à l'aide d'exemples de traductions faites par des professionnels. La section Contextes vous aidera à apprendre l'anglais, l'allemand, l'espagnol et d'autres langues. Vous trouverez ici des exemples de verbes à particule et d'expressions idiomatiques dans des textes dont le style et le thème varient. Les exemples peuvent être triés par traductions et domaines thématiques.

Apprenez des langues étrangères, découvrez les traductions de millions de mots et d'expressions avec des exemples réels de leur utilisation grâce à notre technologie de recherche bilingue !