Sentence examples of "крутящий момент" in Russian
Векторы нагрузки, создающие крутящий момент, действующий на подголовник, изначально лежат в вертикальной плоскости, параллельной средней продольной линии транспортного средства.
The load vectors that generate moment on the head restraint are initially contained in a vertical plane parallel to the vehicle longitudinal centreline.
Если испытательный крутящий момент увеличивается более чем на 10 % по сравнению с первым испытанием для официального утверждения, то повторяется вся программа.
Should the testing moment be increased of more of 10 per cent, when compared to the first approval, the whole programme shall be repeated.
Крутящий момент, прилагаемый к центру коленного шарнира и обусловленный массой металлической трубы и других элементов (кроме самой модели ноги), не должен превышать 25 Нм.
The bending moment applied at the centre of the knee joint, due to the mass of the metal tube and other components (excluding the legform itself), shall not exceed 25 Nm.
Поддерживать уровень нагрузки, создающей этот крутящий момент, в течение не менее 5 с и затем измерить смещение модели головы назад по отношению к смещенной исходной линии туловища.
Maintain the load level producing that moment for not less than 5 seconds and then measure the rearward displacement of the head form relative to the displaced torso line.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной 37 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 37 Nm moment about the R-point.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной 373 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 373 Nm moment about the R-point.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной в 37 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 37 Nm moment about the R-point.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной в 373 Нм вокруг точки R.
Using a 165 ± 2 mm diameter spherical head form, establish the head form initial reference position by applying, perpendicular to the displaced torso line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 373 Nm moment about the R-point.
Определить с помощью сферической модели головы диаметром 165 ± 2 мм и с шероховатостью поверхности, определяемой методом средних квадратов, не более 1,6 мкм, начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной в 36,5 ± 0,5 Нм вокруг [точки R] [точки Н].
Using a 165 ± 2 mm diameter spherical head form with a surface roughness of less than 1.6 μm, root mean square, establish the head form initial reference position by applying, perpendicular to the displaced torso reference line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 36.5 ± 0.5 Nm moment about the [H-point] [R-point].
Определить с помощью сферической модели головы диаметром 165 ± 2 мм и с шероховатостью поверхности, определяемой методом средних квадратов, не более 1,6 мкн, начальное исходное положение модели головы путем приложения перпендикулярно к смещенной исходной линии туловища первоначальной нагрузки в заднем направлении, проходящей по осевой линии сиденья на высоте 65 ± 3 мм ниже верха подголовника, которая должна создавать крутящий момент величиной в 36,5 ± 0,5 Нм вокруг [точки R] [точки Н].
Using a 165 ± 2 mm diameter spherical head form with a surface roughness of less than 1.6 μm, root mean square, establish the head form initial reference position by applying, perpendicular to the displaced torso reference line, a rearward initial load at the seat centreline at a height 65 ± 3 mm below the top of the head restraint that will produce a 36.5 ± 0.5 Nm moment about the [H-point] [R-point].
Examples of word usage in different contexts are provided solely for linguistic purposes, i.e. to study word usage in a sentence in one language and how they can be translated into another. All samples are automatically collected from a variety of publicly available open sources using bilingual search technologies.
If you find a spelling, punctuation or any other error in the original or translation, use the "Report a problem" option or write to us.
If you find a spelling, punctuation or any other error in the original or translation, use the "Report a problem" option or write to us.
In this section, you can see how words and expressions are used in different contexts using examples of translations made by professionals. The Contexts section will help you learn English, German, Spanish and other languages. Here you can find examples with phrasal verbs and idioms in texts that vary in style and theme. Examples can be sorted by translations and topics.
Learn foreign languages, see the translation of millions of words and expressions, and use them in your e-mail communication.
Advert