Beispiele für die Verwendung von "коленчатых патрубков" im Russischen
При использовании устанавливаемого в конце выхлопной трубы дымомера последние 0,6 м трубы должны иметь круглое поперечное сечение, и на этом участке не должно быть никаких коленчатых патрубков и изгибов.
With an end-of-line opacimeter, the terminal 0.6 m of the exhaust pipe must be of circular cross paragraph and be free from elbows and bends.
Материалы с низкой теплостойкостью не должны использоваться для забортных шпигатов, фановых или других отливных патрубков, расположенных близко к ватерлинии, или в местах, где разрушение материалов в случае пожара может привести к затоплению.
Materials with a low resistance to heat shall not be used for overboard scuppers, sanitary discharges or other outlets which are close to the water line, or in places where failure of the material in the event of fire might cause flooding.
В нижней части каждого корпуса должны проверяться не менее 20 % длины каждого кольцевого и продольного сварного шва, а также все сварные швы патрубков и все места, где производились ремонт или полирование ".
For the lower part of each shell at least 20 % of the length of each circumferential and longitudinal weld shall, together with all nozzle welds and any repair or ground areas, be inspected.”.
Загрузочные и разгрузочные отверстия МЭГК должны быть снабжены двумя вентилями, последовательно установленными в доступном месте на каждом из разгрузочных и загрузочных патрубков.
For filling and discharge openings of the MEGC, two valves in series shall be placed in an accessible position on each discharge and filling pipe.
TE8 [5.3.2 21x530 ООН10 ТР6 501 1°] Соединения наружных патрубков резервуара должны изготовляться из материалов, не вызывающих разложения пероксида водорода.
TE8 [5.3.2 21x530 UN10 TP6 501 1°] The connections to the external pipe-sockets of tanks shall be made of materials not liable to cause
" 6.8.3.2.28 Загрузочные и разгрузочные отверстия транспортного средства-батареи или МЭГК должны быть снабжены двумя вентилями, последовательно установленными в доступном месте на каждом из разгрузочных и загрузочных патрубков.
“6.8.3.2.28 For filling and discharge openings of the battery vehicle or MEGC, two valves in series shall be placed in an accessible position on each discharge and filling pipe.
В нижней части каждого корпуса должны проверяться не менее 20 % длины каждого кольцевого и продольного сварного шва, а также все сварные швы патрубков и все зоны, где производились ремонт или полирование ".
For the lower part of each shell at least 20 % of the length of each circumferential and longitudinal weld shall, together with all nozzle welds and any repair or ground areas, be inspected.
Ограничения, касающиеся размеров патрубков и их соответствующей длины, которые могут повлиять на эффективность системы (например, между модулятором и тормозной камерой)
Limitations on tube sizes and associated lengths that have an effect on system performance (e.g. between modulator and brake chamber)
Ограничения, касающиеся размеров трубопровода, патрубков и их соответствующие длины, которые могут повлиять на эффективность системы (например, между модулятором и тормозной камерой)
Limitations on pipe, tube sizes and associated lengths that have an effect on system performance (e.g. between modulator and brake chamber)
Эти резервуары должны подсоединяться к соединительной головке без использования гибких патрубков, и соединение должно иметь внутренний диаметр не менее 10 мм.
These reservoirs shall be connected to the coupling head without using flexible pipes and the connection shall have an internal diameter of not less than 10 mm.
В нижней части каждого корпуса должны проверяться не менее 20 % длины каждого кольцевого или продольного сварного шва, а также все сварные швы патрубков и все зоны, где проводились ремонт или полирование ".
For the lower part of each shell at least 20 % of the length of each circumferential and longitudinal weld shall, together with all nozzle welds and any repair or ground areas, be inspected. ".
Для предотвращения любой потери содержимого в случае повреждения наружных насосов и разгрузочной арматуры (патрубков) первое запорное устройство и его седло должны быть защищены от опасности срывания под воздействием внешних нагрузок или должны иметь такую конструкцию, которая могла бы выдерживать эти нагрузки.
In order to avoid any loss of contents in the event of damage to the external pumps and discharge fittings (pipes), the first closure and its seatings shall be protected against the danger of being wrenched off by external stresses or shall be so designed as to withstand them.
Beispiele für den Wortgebrauch in verschiedenen Kontexten werden ausschließlich zu linguistischen Zwecken bereitgestellt, d. h. um den Wortgebrauch in einer Sprache und Varianten ihrer Übersetzung in eine andere zu untersuchen. Alle Beispiele werden automatisch aus offenen Quellen mit Hilfe einer zweisprachigen Suchtechnologie gesammelt. Wenn Sie einen Rechtschreib-, Zeichensetzungs- oder anderen Fehler im Original oder in der Übersetzung finden, nutzen Sie die Option „Problem melden“ oder schreiben Sie uns.
In diesem Abschnitt können Sie anhand professioneller Übersetzungen sehen, wie einzelne Wörter und Ausdrücke in verschiedenen Kontexten verwendet werden. Kontexte helfen Ihnen, Englisch, Deutsch, Französisch, Spanisch und andere Sprachen zu lernen. Hier finden Sie Beispiele mit Phrasal verbs im Englischen, idiomatischen Ausdrücken und mehrdeutigen Wörtern in einer Vielzahl von Stilen und Themen. Die Beispiele können nach Übersetzung und Themen sortiert werden, und anhand der gefundenen Beispiele kann eine Verfeinerungssuche durchgeführt werden.
Lernen Sie Fremdsprachen und prüfen Sie Verwendung von Wörtern an realen zweisprachigen Beispielen.
Werbung